Slide #1.

Networking Material taken mainly from HowStuffWorks.com
More slides like this


Slide #2.

The Internet A network of networks •Computers •Servers and clients •routers •switches
More slides like this


Slide #3.

Ethernet Network The original Ethernet described communication over a single cable shared by all devices on the network. Once a device attached to this cable, it had the ability to communicate with any other attached device. Each Ethernet devices has a unique address. The Ethernet protocol specifies a set of rules for communication.
More slides like this


Slide #4.

Network Interface Cards (NIC) The computer gives the NIC a message for another networked device and the NIC formats that message for transport over the Ethernet. The reverse is also true, the NIC receives messages from the network and reformats them so that the computer can understand.
More slides like this


Slide #5.

Ethernet Frame
More slides like this


Slide #6.

Switched Ethernet A switch creates a series of instant networks that contain only the two devices communicating with each other at that particular moment. Switches maintain their own Medium Access Control (MAC) look-up tables. These table indicate which network device is at which port on the switch. The look-up tables are constantly updated. When a switch is newly installed, it will construct its table via an Address Resolution Protocol (ARP) broadcast.
More slides like this


Slide #7.

Local Area Network (LAN)
More slides like this


Slide #8.

Virtual LANs Advantages: •Scalability •Security UNCA VLANs: •Dorms •Student, faculty, and labs •CSCI •ENGR and ATMS
More slides like this


Slide #9.

Routers Routers are devices that let messages flow between networks A router uses a configuration table to determine where packets go. A configuration table is a collection of information, including: •Information on which connections lead to particular groups of addresses •Priorities for connections to be used •Rules for handling both routine and special cases of traffic
More slides like this


Slide #10.

Network Addresses Most switches operate at the Data layer (Layer 2) of the OSI Reference Model, while routers operate at the Network layer (Layer 3) When a router receives a packet, it looks at the Layer 3 source and destination addresses to determine the path the packet should take. A standard switch relies on the MAC addresses to determine the source and destination of a packet, which is Layer 2 (Data) networking.
More slides like this


Slide #11.

Open Systems Interconnection (OSI) standard Application Set Layer 7: Application - Layer that interacts with the operating system or application whenever the user chooses to transfer files, read messages or perform other network-related activities. Layer 6: Presentation - Takes the data provided by the Application layer and converts it into a standard format that the other layers can understand. Layer 5: Session - Establishes, maintains and ends communication with the receiving device. Transport Set Layer 4: Transport - Maintains flow control of data and provides for error checking and recovery of data between the devices. Layer 3: Network - Logical routing and addressing are handled here. Layer 2: Data – Assigns the appropriate physical address. Layer 1: Physical - This is the level of the actual hardware.
More slides like this


Slide #12.

Why Protocol Hierarchies The philosopher-translator-secretary architecture.
More slides like this


Slide #13.

Protocol Layering and Data • Each layer takes data from above • adds header information to create new data unit • passes new data unit to layer below
More slides like this


Slide #14.

IP Address • Each machine on the Internet is assigned a unique address called an IP address. IP stands for Internet protocol, and these addresses are 32-bit numbers, normally expressed as four "octets" in a "dotted decimal number." • Example: 216.27.61.137 • Every machine on the Internet has a unique IP address.
More slides like this


Slide #15.

Names • People have trouble remembering the strings of numbers that make up IP addresses, and because IP addresses sometimes need to change, all servers on the Internet also have human-readable names, called domain names. • A set of servers called Domain Name Servers (DNS) maps the human-readable names to the IP addresses. These servers are simple databases that map names to IP addresses, and they are distributed all over the Internet. • Example: www.howstuffworks.com for 209.116.69.66
More slides like this


Slide #16.

Clients and Servers Any server machine makes its services available to the Internet using numbered ports, one for each service that is available on the server. Logical port numbers correspond to application layer programs. These port numbers are included in the address information of a packet. Here are some common port numbers: •echo 7 •daytime 13 •qotd 17 (Quote of the Day) •ftp 21 •telnet 23 •smtp 25 (Simple Mail Transfer, i.e., e-mail) •time 37 •nameserver 42 •nicname 43 (Who Is) •gopher 70 •finger 79 •WWW 80
More slides like this


Slide #17.

Things to try • Type “IPCONFIG” at the MSDOS prompt • Type “tracert www.cs.unca.edu” at the MSDOS prompt. • Type “arp –a” at the MSDOS prompt.
More slides like this


Slide #18.

WinSCP Secure FTP • File Transfer Protocol – used to transfer files from one machine to another • Select start -> CSCI programs -> WinSCP • Features – It’s free! (http://winscp.sourceforge.net/eng/) – Provides a dual panel display – Copy and move files and folders (to and from a remote computer). – Rename files and folders – Create new folders – Change properties of files and folders – Edit files
More slides like this


Slide #19.

WinSCP Assignment • Logon: – User Name: first 6 letters of last name followed by first initial and middle initial – Password: CSCI followed by last 4 digits of student id
More slides like this


Slide #20.

WinSCP Assignment (continued) • Create a directory named public_html in your CS home directory. – Select your CS directory window (the right pane of the WinSCP window); assure that the title bar of that window is blue. – Use the Create Directory button at the bottom of the WinSCP window to create a directory named public_html
More slides like this


Slide #21.

WinSCP Assignment (continued) • Open your public_html directory by double-clicking on it. • Transfer your webpage to your public_html directory on candler and give it the name, “index.html” • Set the file and folder properties to allow the world to view your file – Select the folder or file and rightclick, then select Properties – Set the properties as shown on the right • View your page in your browser using the following address www.cs.unca.edu/~userName Put your User name here
More slides like this